Cela peut entraîner des dommages irréversibles. Utilisation du support basculant : REMARQUE : NE POSEZ JAMAIS VOTRE TÉLÉVISEUR FACE CONTRE LE SOL. Si le panneau arrière plat de votre téléviseur plasma ou LCD nécessite une vis de diamètre M4 ou M5, enfilez une vis M4 x 12 mm (A) ou M5 x 12 mm (C) à travers la rondelle frein correspondante (L, M), une rondelle M4/M5, le bras basculant et le téléviseur, comme indiqué dans le schéma 1. Se recomienda que mida la distancia entre los agujeros roscados de instalación en la parte trasera de su televisor antes de fijar los brazos de extensión.įrench Installation instructions Support mural fixe/basculant pour téléviseur LCD ou plasma - Modèles : FT6503*, FT65B-CC*, ELLCDM-07,ELLCDP-07, LM50CDM, DC50CDM, LM60T, DC60T, LM65FT*, DC65FT* Plaque murale Bras d’inclinaison NE RENVOYEZ PAS CE PRODUIT AU MAGASIN OU SITE WEB OÙ VOUS L’AVEZ ACHETÉ! SI VOUS ESTIMEZ QUE CE SUPPORT EST DÉFECTUEUX, QUE CERTAINES DE SES PIÈCES SONT MANQUANTES OU CASSÉES, OU SI VOUS AVEZ DU MAL À FIXER LEDIT SUPPORT À VOTRE MUR OU À INSTALLER VOTRE TÉLÉVISEUR, VEUILLEZ COMMUįixation du support d’écran au téléviseur LCD ou plasma: PANNEAU ARRIERE PLAT PANNEAU ARRIERE EN RETRAIT Un téléviseur plasma ou LCD avec un panneau arrière plat nécessite une vis plus courte. Si necesita utilizar los brazos de extensión, debe utilizarlos todos a efectos de que la base pueda dar un apoyo adecuado a su televisor. Si cuenta con un televisor de plasma/LCD demasiado grande, es posible que tenga que utilizar los brazos de extensión proporcionados. Brazo de Barra horizontal inclinación de ajuste Colocación del sistema sujetacables: 4.Ĭómo fijar los brazos de extensión: (Nota: No compatible con todos modelos) 4. Tras haber colocado los brazos de inclinación en la barra de ajuste horizontal, vuelva a atornillar los casquillos. Desatornille los casquillos de extremo de ambos lados y coloque los brazos de inclinación (figura 7). El colocar el televisor apoyado sobre su vidrio puede causarle daños permanentes. Consulte el diagrama 1 a continuación para ver la instalación en detalle.Ĭomo soporte inclinado: NOTA: EVITE COLOCAR SU TELEVISOR CON LA PANTALLA HACIA ABAJO Y APOYADO SOBRE SU VIDRIO. En aparatos de plasma/LCD con parte trasera plana de tornillos de diámetro M4 o M5, enrosque al televisor un tornillo M4 x 12 (A) o M5 x 12 (C) a través del brazo de inclinación, la arandela de seguridad correspondiente (L o M) y una arandela M4/M5. Modelos: FT65-03*, FT65B-CC*, ELLCDM-07,ELLCDP-07, LM50CDM, DC50CDM, LM60T, DC60T, LM65FT*, DC65FT* Travesaño de apoyo Cordón de C Brazos de enrutamientobles inclinación NO DEVUELVA ESTE PRODUCTO A LA TIENDA O SITIO WEB EN EL QUE LO COMPRÓ.Ĭómo fijar la placa del televisor al televisor de LCD o de plasma: PARTE TRASERA PLANA PARTE TRASERA CON RANURAS Los televisores de respaldo plano utilizan pernos más cortos. It is recommended to measure the distance between the mounting holes on the back of your TV prior to attaching the Extension Arms.Įspanol Installation instructions Soporte fijo para televisores de plasma/ LCD. If you need to use the Extension Arms, you must use all Extensions Arms in order for the Mount to properly hold your TV. If you have an oversized LCD/ Plasma TV, you may need to use the Extension Arms provided. Once the Tilts Arms are slid onto the Horizontal Adjustment Bar, screw on End Caps.Īttaching Extension Arms: (Note: Some models not included) 4. Unscrew the End Caps from both sides and attach the Tilt Arms by sliding them on (Figure7). Laying the television down on the glass may cause permanent damage. Using as a Tilt Mount: NOTE: NEVER LAY YOUR TELEVISION FACE DOWN ON ITS GLASS. Tighten bolts firmly with a Phillips screwdriver. Please see Diagram 1 below for a detailed drawing. For a flat back Plasma/LCD that required a M4 or M5 diameter bolt, thread a M4 x 12(A) or a M5 x 12(C) bolt through the appropriate Lock Washer(L,M), an M4/M5 Washer, the Tilt Arm and into the TV. Wall Plate specifically to hold LCD TV’s 34” - 65” and a maximum weight of up to 200lbs.Īttaching Monitor Bracket to a LCD/Plasma with: FLAT BACK RECESSED BACK Plasma/LCDs with a flat back panel will require a shorter bolt. Do not screw too tight until all the screws are in. English Installation instructions Fixed/Tilt Plasma/LCD Wall Mount Model: FT65-03*, FT65B-CC*, ELLCDM07,ELLCDP-07, LM50CDM, DC50CDM, LM60T, DC60T, LM65FT*, DC65FT* ! CAUTION This wall mount was designed wall, screw 1 Dry Wall Screw and 1 Dry Wall Washer (P & Q) in the upper left mounting hole of the Wall Plate.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |